Black Friday Deals! $100 off every Gauge
Docs / Tyre Pressure (TPMS) Display with a Haltech ECU
How-to & Guides

Tyre Pressure (TPMS) Display with a Haltech ECU

Show all four tyre pressures and temperatures from Haltech TPMS on a 52mm or 60mm gauge, laid out like the car, with a warning when one drops.

KrispyGauge 60mm tyres page showing four tyre pressures laid out like the car
The Tyres template: one bar per corner, laid out like the car.

A slow puncture is easy to miss until the car starts to feel wrong, and on track a tyre that is too hot or too soft costs time long before it fails. KrispyGauge shows all four tyre pressures on one page, laid out like the car, and warns you when one drops.

What you need

  • A KrispyGauge (52mm or 60mm).
  • A Haltech ECU (Elite, Nexus or NSP) with Haltech's TPMS kit set up, so the ECU receives the four wheel sensors.

The ECU puts each tyre's pressure and temperature on its CAN bus, and KrispyGauge reads them there. Pressures are shown as a tyre gauge shows them, above atmospheric. If the tyre pressures show up in Haltech's NSP software, the gauge can show them.

What it reads

  • Pressure for each corner: Tyre FL, Tyre FR, Tyre RL, Tyre RR, in psi or kPa.
  • Temperature for each corner: Tyre Tmp FL to Tyre Tmp RR, in °C or °F.
  • The recommended pressures front and rear, and a leak flag per tyre, as set up in the ECU.

The full list is on the Haltech signals page.

How to set it up

  1. Set up Haltech TPMS in NSP and check all four tyres read with the car stopped.
  2. Connect the KrispyGauge to the ECU's CAN bus.
  3. With the ignition on, join the gauge's WiFi network Krispy_XXXX (password GetKrispy) and open http://4.3.2.1.
  4. Under Settings, choose Haltech as the ECU first, since changing it later resets your pages. Set Pressure to psi or kPa.
  5. Under Page Config, pick the Tyres template and set its four channels to Tyre FL, Tyre FR, Tyre RL and Tyre RR, in that order.
  6. Give each one a low Warning value (below) and save.

Connection help is in connecting to the Web UI.

Warn when a tyre drops

KrispyGauge 52mm tyres page with the rear left tyre low, then an amber TYRE RL LOW alert
A slow puncture in the rear left: its bar turns red, then a generic alert takes the screen.

There are two levels, and they work well together:

  • On the page. Give each tyre a Min warning value. A tyre below it turns the warning colour on the tyres page, so you can see which corner it is.
  • Fullscreen. Under Alerts, set up a Generic Alert for each tyre with Alert Below set, words like TYRE RL LOW, and Show Value on. It flashes over whatever page you are on.

A good starting point is your cold pressure less 15 to 20%. There are four generic alerts, so one per tyre uses them all; if you need some for other readings, put the alert on the tyres you worry about most. More on alerts in warnings and alerts.

Which template?

  • Tyres for all four pressures laid out like the car.
  • 4 Bars or Quad Value for the four temperatures, on a second page.
  • Page Rules under Alerts can jump to the tyres page by itself when a pressure drops.

Common questions

Does it work without a Haltech ECU?

Not today. The gauge reads the tyre data a Haltech ECU puts on the bus, and none of the other supported ECUs send tyre pressures.

Can it show tyre temperatures?

Yes. Each corner's temperature is its own reading, so put them on any page or set a high-temperature alert on them.

← All docs