Black Friday Deals! $100 off every Gauge
Docs / Warnings and Alerts: How KrispyGauge Tells You Something Is Wrong
How-to & Guides

Warnings and Alerts: How KrispyGauge Tells You Something Is Wrong

Set warning limits on any reading, and fullscreen alerts for low oil pressure, high temperatures, a lean wideband or a dead alternator. How each one works and how to set it up.

KrispyGauge oil pressure gauge; when pressure drops it shows a fullscreen red STOP THE CAR alert with the reading under it
When oil pressure drops, the alert takes over the whole screen, in your own words.

A gauge you have to look at is only half a gauge. The other half is telling you when to look. KrispyGauge has two kinds of warning: a limit on any reading on a page, which turns that reading the warning colour, and fullscreen alerts, which take over the whole screen whatever page you are on.

Both are set up in the gauge's Web UI, and you can try every one of them in the live demo before you buy.

Warning values on a page

KrispyGauge four-value page with the coolant reading in red at 108 degrees while oil temperature, oil pressure and voltage stay white
Coolant past its 105 °C warning value. The other three readings carry on as normal.

Every reading on every page has a Warning value with a Min and a Max box, under the reading's channel in Page Config. Leave a box blank to switch that side off.

When a reading goes past one, it changes to the page's Warning colour, red unless you pick another. Dials and bars mark the same limit on their scale, so you can see how close you are before you reach it. The rest of the page carries on as normal.

This is the quiet kind of warning: right for a reading you glance at anyway, such as coolant on a four-value page or one tyre on the tyres page. Under Settings, Auto Range from Warning Value sizes each dial to its warning value, so a 20 psi boost warning gives a dial that ends at 25 psi.

Fullscreen alerts

KrispyGauge 60mm showing an amber HIGH COOLANT alert at 112 degrees
A temperature alert: amber, with the reading under it.

A fullscreen alert covers the whole display in a flashing colour with a few words in large letters, whichever page is showing. It is for the things you cannot afford to miss with your eyes on the road or the track. All of them are under Alerts in the Web UI, and every one is off until you switch it on.

  • Oil Pressure Alert (red). Alerts below and/or above the pressures you set, and stays quiet under 300 RPM so it does not go off with the engine stopped. Only When adds a second condition, such as only while RPM is above 3000, held for a set time: that catches pressure falling away under load, which a warm idle would hide.
  • Temperature Alerts (three, amber). Pick any temperature your ECU sends: coolant, oil, intake air, EGT, gearbox. Set a low limit, a high limit or both, in your display units.
  • Generic Alerts (four, amber). The same for any reading at all: fuel pressure, boost, ethanol content, a tyre. The alert shows the reading's name.
  • Wideband Alerts (two). A RICH or LEAN warning, either against fixed lambda or AFR limits, or against your target lambda or a second wideband, as a percentage difference. Ignore Transients waits for 2 seconds of it with the engine running, so fuel cut on a lift and a hard stab of throttle do not set it off.
  • Alternator Not Charging (orange). Battery voltage below a value you set for 5 seconds, with the engine running (above 500 RPM). A healthy car holds about 13.5 to 14.7 V.
  • Check Engine Light. Shows the ECU's CEL on the gauge, either as a lamp on the page or as a fullscreen warning.
  • Pit Limiter Alert (green). Flashes while the ECU's pit limiter is on.

Every alert can have its own words and, with Show Value, the live reading under them. The temperature and generic alerts can also have their own colours. When the reading comes back inside its limits, the alert clears and the page you were on is still there.

Set one up

  1. With the ignition on, join the gauge's WiFi network Krispy_XXXX (password GetKrispy) and open http://4.3.2.1. Help is in connecting to the Web UI.
  2. Check your ECU type and units under Settings. Alert values are in the units you display, so set psi or kPa, °C or °F first.
  3. Open Alerts and switch on the alert you want.
  4. Pick the reading it watches, where it asks, and fill in Alert Below, Alert Above or both. Leave a box blank to leave that side unarmed.
  5. Change the words if you like, switch on Show Value, and save.

Good starting values

  • Oil pressure: a little below what your engine shows at a hot idle, and use Only When for a higher limit above 3000 RPM. Your engine builder can give you the real figures. See the oil pressure guide.
  • Coolant: above 105 to 110 °C for most road engines. See the water temperature guide.
  • Oil temperature: above about 130 °C on track. See the oil temperature guide.
  • EGT: a high limit per cylinder from your tuner. See the EGT guide.
  • Wideband: lean above λ 1.10 under load, or 10% off target. See the wideband guide.
  • Tyres: a generic alert per tyre, below your cold pressure less 15 to 20%. See the TPMS guide.

More than a warning

The Alerts tab has three more ways for a reading to change what the gauge does:

  • Shift Light Takeover. Up to four RPM stages, each filling the screen with its own colour; the last one strobes. Stages must rise from first to fourth, between 3000 and 20000 RPM.
  • Page Rules (six). Switch to a chosen page while a reading is above or below a value, such as the boost page above 5 psi, and go back 2 seconds after it comes back inside.
  • Keypad Actions (three). Turn a CAN keypad button on when a reading goes past a limit and off again when it returns, so the ECU can act on it: a fan, a pump, a boost map.

Common questions

Do alerts work on every page?

Yes. Fullscreen alerts watch their reading all the time, whether or not it is on the page you are looking at. Warning values belong to the page they are set on.

Can an alert sound a buzzer?

The gauge warns on its screen. To drive a buzzer or a light, use a Keypad Action to switch a keypad button your ECU has wired to an output.

Can I try them before I buy?

Yes. Open the live demo, go to Alerts, switch one on, and set a limit the simulated engine will cross.

← All docs