Black Friday Deals! $100 off every Gauge
Docs / How to Set Up KrispyGauge as an Oil Pressure Gauge
How-to & Guides

How to Set Up KrispyGauge as an Oil Pressure Gauge

Show live oil pressure from your ECU on a 52mm touchscreen gauge, with a full-screen low oil pressure warning. Which ECUs work, factory cars, and setup.

KrispyGauge Smiths Classic style oil pressure gauge, needle rising from 30 to 60 psi
Oil pressure on the Smiths Classic template, with a low-pressure warning set.

Oil pressure is the reading that saves engines. When it drops, you have seconds to back off before bearings start to suffer, and a factory warning light often comes on too late. KrispyGauge shows oil pressure as a live number or dial on a 52mm or 60mm colour touchscreen, and it flashes a full-screen alert the moment pressure falls below a limit you set.

What you need

  • A KrispyGauge (52mm or 60mm) to fit a standard gauge pod or dash panel.
  • An oil pressure sensor that something on the CAN bus reads, which usually means one of these:
    • an aftermarket ECU with an oil pressure sensor wired in and set up, or
    • a CAN sensor module such as the AEM CSM6, for cars without one (see below).

KrispyGauge doesn't wire to the sensor itself. It reads the pressure the ECU or module has already measured, over CAN. If your ECU software shows oil pressure, KrispyGauge can show it on the dash.

ECUs that send oil pressure

KrispyGauge reads oil pressure from these ECUs' CAN data:

Megasquirt works with KrispyGauge for other readings, but KrispyGauge doesn't currently read oil pressure from it.

Factory cars: why OBD2 can't show oil pressure

OBD2 has no standard reading for oil pressure, and most factory cars don't even have a real oil pressure sensor, only a pressure switch that turns the warning light on. So no OBD2 gauge can show oil pressure on a standard car, whatever its box says.

To see real oil pressure on a car without an aftermarket ECU, fit a pressure sensor and read it through a CAN sensor module. KrispyGauge supports the AEM 30-2226 CSM6. Its four analog inputs take 0–5V sensors, and you enter each sensor's calibration in the gauge so the voltage becomes psi or kPa. The module also sends RPM, fuel level and battery voltage. See the AEM CSM6 page for details.

If you don't need oil pressure itself, plenty of other engine readings come straight through the OBD2 port, including water temperature, boost and, on many cars, oil temperature.

How to set it up

  1. Make sure your ECU (or sensor module) is reading oil pressure. If its own software shows a sensible number with the engine running, you're ready.
  2. Connect the KrispyGauge to the same CAN bus.
  3. With the ignition on, join the gauge's WiFi network Krispy_XXXX (password GetKrispy) and open http://4.3.2.1.
  4. Under Settings, choose your ECU type first, since changing it later resets your pages. Set Pressure units to PSI or kPa.
  5. Under Page Config, pick a template and set its channel to Oil Pres (oil pressure). A range of 0 to 100 psi suits most engines.
  6. Set a minimum warning (below) and save.

Connection help is in connecting to the Web UI.

Set a low oil pressure warning

This is the most useful thing the gauge does. Give the oil pressure page a minimum warning threshold. If pressure drops below it, from oil surge in a long corner, a failing pump or a leak, the whole screen flashes a warning.

A good starting point is a little below what your engine shows at a warm idle. Your engine builder can give you the right figure. You can also set a maximum warning to catch a stuck relief valve on a cold start.

Which template?

  • Dial (single) or Classic Needle for a traditional oil pressure gauge.
  • Dual Value with oil pressure and RPM side by side. Pressure that falls as revs rise is worth knowing about.
  • Quad Value for oil pressure, oil temperature, water temperature and battery voltage on one page.
  • Histogram to watch pressure over the last few seconds, which is where oil surge shows up on track.

Common questions

Can I wire my oil pressure sensor straight to the KrispyGauge?

No. KrispyGauge reads over CAN only. Wire the sensor to your ECU, or to a CAN sensor module like the AEM CSM6.

Why does my OBD2 gauge not list oil pressure?

Because standard OBD2 doesn't include it, and most factory engines don't measure it. A sensor module is the way to add it.

Can it show psi or kPa?

Yes. Pressure can be shown in psi, kPa or kPa absolute.

← All docs