Black Friday Deals! $100 off every Gauge
Docs / How to Set Up KrispyGauge as a Water Temperature Gauge
How-to & Guides

How to Set Up KrispyGauge as a Water Temperature Gauge

See your engine's real coolant temperature through the OBD2 port or your ECU, with no sender to fit. A 52mm touchscreen water temp gauge with overheat warnings.

KrispyGauge BMW Style coolant gauge with a needle between cold and hot marks, reading 89 °C
The BMW Style template: the needle you know, with the actual temperature under it.

Plenty of modern cars no longer have a real temperature gauge. Some have a needle that sits in the middle across a wide range of temperatures, and some only have a warning light that comes on when the engine is already overheating. KrispyGauge shows the actual coolant temperature as a number or dial, in °C or °F, on a 52mm or 60mm colour touchscreen. On most cars it plugs straight into the OBD2 port.

What you need

  • A KrispyGauge (52mm or 60mm) to fit a standard gauge pod or dash panel.
  • One of these to read from:
    • your car's OBD2 port, using our plug-in OBD cable, or
    • an aftermarket ECU with a CAN output.

There's no sender to fit and no coolant hose to cut into. The engine's own temperature sensor already does the work.

Water temperature over OBD2

Coolant temperature is one of the most widely reported OBD2 readings, so if your car's OBD2 works with KrispyGauge, you'll almost certainly get it. KrispyGauge reads OBD2 on cars that use CAN for it, which is most cars from about 2008 onwards. Older K-Line cars can connect through the Krispy K-Line adaptor. Check yours on the OBD2 supported vehicles list.

Over OBD2 you also get readings like intake air temperature, battery voltage, boost on turbo cars and, on many cars, oil temperature. That's enough to replace a row of separate gauges.

Water temperature from an aftermarket ECU

Every aftermarket ECU KrispyGauge supports sends coolant temperature: Haltech, Link, MaxxECU, Holley EFI, Megasquirt, AEM Infinity, EcuMaster EMU Black, Emtron, rusEFI and Syvecs. Haltech, MaxxECU, Emtron and Syvecs can also send coolant pressure if you have a sensor fitted, which helps catch a failing head gasket or radiator cap early.

Every reading is listed on each ECU's supported signals page, linked from the docs index.

How to set it up

  1. Plug the gauge into the OBD2 port or your ECU's CAN bus. For OBD2, read the OBD2 setup guide first, especially the part about powering the gauge from an ignition-switched feed.
  2. With the ignition on, join the gauge's WiFi network Krispy_XXXX (password GetKrispy) and open http://4.3.2.1.
  3. Under Settings, choose your ECU type first (OBD for a factory car), since changing it later resets your pages. Set Temperature to Celsius or Fahrenheit.
  4. Under Page Config, pick a template and set its channel to Cool Tmp (coolant temperature).
  5. Set a maximum warning (below) and save.

Connection help is in connecting to the Web UI.

Set an overheating warning

Give the coolant temperature page a maximum warning a few degrees above where your engine normally runs once it's warm. If the temperature climbs past it, from a failing fan, a leak or a hot day in traffic, the gauge flashes a full-screen alert. That gives you time to pull over before the engine is damaged, which a factory warning light often doesn't.

To find your normal figure, drive for a while with the gauge on and note where the number settles.

Which template?

  • Single Value shows a large number, the clearest way to see small changes.
  • Dial (single) or Classic Needle for a traditional water temperature gauge.
  • Background Fill fills the screen with colour as the temperature rises.
  • Quad Value for coolant, intake air temperature, battery voltage and boost on one page.

Common questions

Will it work on my car?

If your car uses CAN for OBD2 (most from about 2008 on), almost certainly. Older cars may need the K-Line adaptor. Check the supported vehicles list.

Do I need to fit a temperature sender?

No. KrispyGauge reads the engine's own coolant sensor through the ECU.

Why does my KrispyGauge read differently from my car's dash gauge?

Many factory gauges are deliberately damped so the needle sits still across a wide normal range. KrispyGauge shows the real number the ECU reports.

Can it show °F?

Yes. Temperature can be shown in Celsius or Fahrenheit.

← All docs