Black Friday Deals! $100 off every Gauge
Docs / How to Set Up KrispyGauge as a Digital Boost Gauge
How-to & Guides

How to Set Up KrispyGauge as a Digital Boost Gauge

Turn KrispyGauge into a digital boost gauge that reads boost straight from your ECU or OBD2 port. No sensor, no vacuum line. Setup, overboost warnings and FAQs.

KrispyGauge Boost Peak page sweeping from vacuum into 19 psi, with the peak held underneath
The Boost Peak template: vacuum and boost on one arc, with the peak held under it.

A boost gauge is usually the first gauge anyone fits to a turbo or supercharged car. A traditional one needs a sensor, a vacuum line teed into the intake manifold and a wire through the firewall. KrispyGauge doesn't need any of that. Your ECU already measures manifold pressure, so KrispyGauge reads it straight off the CAN bus or the OBD2 port and shows it on a 52mm or 60mm colour touchscreen, with vacuum and boost on the same scale.

What you need

  • A KrispyGauge (52mm or 60mm) to fit a standard gauge pod or dash panel.
  • A way to read your engine's manifold pressure, which is one of these:
    • an aftermarket ECU with a CAN output (Haltech, Link, MaxxECU and others below), or
    • a factory car's OBD2 port, using our plug-in OBD cable.

That's it. There's no separate boost sensor to buy and no hose to run.

Boost from an aftermarket ECU

Every aftermarket ECU KrispyGauge supports sends manifold pressure over CAN, and the gauge turns it into boost for you. That covers:

  • Haltech (Elite, Nexus, NSP), Link, MaxxECU, Holley EFI, Megasquirt, AEM Infinity, EcuMaster EMU Black, Emtron, rusEFI and Syvecs.

Some ECUs send more than plain boost:

  • Boost target from Haltech, MaxxECU, Emtron and Syvecs. Put it beside actual boost to see how closely the boost control tracks.
  • Pre-intercooler boost and wastegate pressure from Haltech.

Each ECU's full list is on its supported signals page, for example Haltech, Link or MaxxECU. Every other ECU is linked from the docs index.

Boost from OBD2 on a factory car

On a factory turbo car, including most turbo-diesel utes, KrispyGauge reads manifold pressure through the OBD2 port. It works on cars that use CAN for OBD2 (most cars from about 2008 on). Older cars that talk K-Line can use the Krispy K-Line adaptor. See the OBD2 supported vehicles list to check yours.

Three things to know about OBD2 boost:

  • It tops out at about 22 psi (152 kPa). The standard OBD2 reading can't go above 255 kPa absolute, so a car making more boost than that will show 22 psi at the top. Most factory cars stay under it.
  • It updates more slowly than an aftermarket ECU, because OBD2 is question-and-answer. It's fine for watching boost build, but it won't flicker the way a broadcast CAN reading does.
  • Boost is measured against standard sea-level pressure (101.3 kPa). At altitude, vacuum and boost read a little lower than a gauge referenced to the air around you.

How to set it up

  1. Wire the gauge to your ECU's CAN bus or the OBD2 port. Our OBD2 setup guide covers OBD2 wiring and power.
  2. With the ignition on, join the gauge's WiFi network Krispy_XXXX (the name shows on the gauge at boot). The password is GetKrispy.
  3. Open http://4.3.2.1 to reach the Web UI. If it won't load, see connecting to the Web UI.
  4. Under Settings, choose your ECU type first. Changing it later resets your pages. Set Pressure units to PSI or kPa.
  5. Under Page Config, pick a template and set its channel to Boost. Set the range to suit your engine, for example −15 to 25 psi.
  6. Save. Your boost gauge is live.

Which template?

  • Dial (single) or Classic Needle look like a traditional boost gauge. A sweep through vacuum into boost is easy to read at a glance.
  • Single Value gives one big number if you want the exact figure.
  • Histogram shows the last few seconds as a graph, which is handy for spotting boost creep or a slow spool.
  • Dual Value puts boost next to another channel, such as boost target or AFR.

The gauge holds several pages, so boost can sit alongside oil pressure, water temperature or AFR. A tap on the screen switches between them.

Set an overboost warning

Give the Boost page a maximum warning a little above the boost you're tuned for. If boost spikes past it, from a stuck wastegate, a split hose or a boost controller fault, the gauge flashes a full-screen alert you can't miss.

Haltech: change boost maps from the gauge

On a Haltech, KrispyGauge can also act as a CAN keypad. Touch buttons on the screen can switch boost maps, arm launch control or change traction settings, set up in Haltech NSP like a physical keypad. See Use your KrispyGauge as a Haltech CAN keypad.

Common questions

Do I need a separate boost sensor?

No. KrispyGauge reads the manifold pressure your ECU already measures, over CAN or OBD2. Nothing connects to the intake manifold.

Will it show vacuum as well as boost?

Yes. Below atmospheric pressure the reading goes negative, so one gauge shows vacuum at idle and boost under load.

Why does my OBD2 boost stop at 22 psi?

That's the limit of the standard OBD2 manifold pressure reading, not the gauge. With an aftermarket ECU there's no such cap.

Does it work on diesels?

Yes, if the engine reports manifold pressure over OBD2, as most modern turbo-diesels do. The 22 psi OBD2 limit still applies.

Can I show boost in kPa?

Pressure can be shown in psi, kPa or kPa absolute.

← All docs