Black Friday Deals! $100 off every Gauge

Use cases · Make it yours

Many uses.
One gauge.

A 52mm or 60mm round touchscreen that reads whatever is on your CAN bus. Add exhaust temps and it is an EGT display. Add a wideband and it is an AFR gauge. Turn on Bluetooth and it feeds your lap timer. Same gauge, set up your way from your phone.

Grows with your build

Same gauge. New job.

KrispyGauge shows whatever your car has to say. Add exhaust temps, a wideband, tyre pressures or a lap timer, and it becomes the gauge for that: on a page you choose, with the warnings you set.

KrispyGauge 60mm showing four exhaust gas temperatures from a Haltech TCA as bar graphs, cylinder 3 running hotter than the rest at around 910 °C

Use your gauge as an

Per-cylinder EGT display

KrispyGauge × Haltech TCA

Add a Haltech TCA thermocouple amplifier and the gauge shows exhaust gas temperature for every cylinder, so you can see the one running leaner or hotter than the rest. It reads the TCA straight off the CAN bus, alongside your ECU or with no ECU at all.

  • Up to eight EGT channels from a TCA-8, or two and four from a TCA-2 and TCA-4
  • A full-screen alert when any cylinder passes your limit
  • Also reads the AEM 30-2224 eight-channel module (beta)
KrispyGauge 52mm showing lambda for both banks of a Haltech WB2, then switching to the Lambda Target page with bank 1 just rich of its 0.82 target

Use your gauge as a

Wideband AFR gauge

KrispyGauge × Haltech WB1 / WB2

A Haltech WB1 or WB2 and a KrispyGauge make a complete wideband gauge: lambda or AFR for one or two sensors, 20 times a second. No Haltech ECU needed, so it suits a factory-ECU car as well as a built one.

  • One sensor with a WB1, two banks with a WB2
  • Lean warning on the side of your target you choose
  • A sensor fault blanks the reading rather than freezing it

Wideband controller support is in beta.

KrispyGauge 60mm Haltech-style dash showing RPM and speed climbing, the readings it streams to the VRacer lap timing app

Use your gauge as a

Data logger for lap timing

KrispyGauge × VRacer

While it shows your readings on the dash, the gauge streams the same ECU data to the VRacer app on your phone over Bluetooth. Every lap comes with RPM, boost, temperatures and lambda beside it, with no extra dongle or wiring.

  • Lap times and splits from your phone, 1,600+ tracks preloaded
  • Engine data on every lap, for comparisons and video overlays
  • iPhone and Android
KrispyGauge 52mm on the Value + Key Adj page: the + key is tapped three times, its LEDs light one by one, and the boost target steps from 14 to 20 psi

Use your gauge as a

Boost map switch with display

KrispyGauge × Haltech keypad

On a Haltech, the gauge doubles as a CAN keypad. The Value + Key Adj page puts live boost up top and two touch keys below it, set up in NSP to switch boost maps or step the boost target, so the button and the result are on the same screen. Tap one and the gauge shows the new target for a moment, then goes back to boost.

  • Live boost and two keys on one page (Value + Key Adj)
  • Up to eight keys on the full keypad page, assigned in Haltech NSP
  • Works beside a physical keypad on the other ID

The ECU does the boost control; the gauge switches its maps and shows the result.

KrispyGauge 60mm tyres page showing four tyre pressures of 31 to 34 psi, laid out like the car

Use your gauge as a

Tyre pressure (TPMS) display

KrispyGauge × Haltech TPMS

With Haltech's TPMS kit set up on a Haltech ECU, the ECU puts all four tyre pressures and temperatures on the CAN bus. The gauge shows them on a tyres page laid out like the car, with a warning when one drops.

  • Pressure and temperature for each corner
  • Low-pressure warning per tyre
  • Shown in psi or kPa

Read through a Haltech ECU, which receives the TPMS sensors.

KrispyGauge 52mm flicking through custom screens: a splash screen where a car's headlights flicker on under the words Welcome back, boost over an animated synthwave sunset, a turbo snail meme, RPM over animated flames, a check engine light meme, and speed and RPM over an animated targeting computer display

Personalise your gauge with

Custom gauge backgrounds and splash screens

KrispyGauge × Your own images

Make the gauge look like nobody else's. Upload your own splash screen for start-up, put a picture or an animated GIF behind any page and your readings sit right on top of it, or give a page over to a picture on its own: your car, your club's logo, or the meme that gets a laugh at every meet.

  • Your own splash screen when the gauge starts up
  • Still images or animated GIFs behind your live readings
  • A page that is just a picture, to flick to whenever you like

Uploaded from your phone in the gauge's web app. No computer needed.

One reading, done right

Replace a gauge. Skip the sender.

Your ECU, or a factory car's OBD2 port, already measures these. The gauge reads them over CAN, so there is nothing to tee in and no wire through the firewall.

Warnings

And it tells you when something's wrong.

Give any reading a warning value and it turns red past it. Switch on a fullscreen alert and it takes over the whole screen, whatever page you're on: low oil pressure, an engine running hot, a lean wideband, a tyre going down, an alternator that's stopped charging.

  • Warning values on every reading, high and low
  • Fullscreen alerts for oil, temperatures, wideband, battery and any reading you pick
  • Your own words, colours and the live reading on each alert
KrispyGauge 52mm oil pressure gauge; when pressure drops it shows a fullscreen red STOP THE CAR alert
Low oil pressure
KrispyGauge 60mm four-value page; coolant climbs past its 105 °C warning value and flashes red
Warning value
KrispyGauge 60mm coolant gauge; as it climbs past 108 °C the screen turns amber with a HIGH COOLANT alert
Running hot

And a few more

Make it yours.

Not sure your setup is covered? Ask in the KrispyGauge Facebook group or request a feature.

Shop KrispyGauge