Black Friday Deals! $100 off every Gauge
Docs / KrispyGauge as a Multi-Function Gauge: Every Reading in One Pod
How-to & Guides

KrispyGauge as a Multi-Function Gauge: Every Reading in One Pod

One 52mm or 60mm touchscreen gauge for boost, oil pressure, temperatures, AFR and more, read from your ECU over CAN or a factory car's OBD2 port.

KrispyGauge four-value page showing coolant 88, oil temperature 101, oil pressure 56 and 14.1 volts
Four readings on one page with the Quad Value template.

Boost, oil pressure, oil temperature, water temperature, AFR and voltage used to mean six gauges, six senders and a pillar pod full of holes. KrispyGauge replaces them with one: a 52mm or 60mm round colour touchscreen that reads everything from your ECU over CAN bus, or from a factory car's OBD2 port. A tap switches between pages, and each page can show one reading or several.

What one gauge can show

What's available depends on what your ECU measures. Each of these has its own setup guide:

Haltech ECUs send the most, with over 180 readings. Every reading for every ECU is listed on its supported signals page, linked from the docs index.

Works with your ECU, or your factory car

  • Aftermarket ECUs: Haltech, Link, MaxxECU, Holley EFI, Megasquirt, AEM Infinity, EcuMaster EMU Black, Emtron, rusEFI and Syvecs.
  • Factory cars: any car using CAN for OBD2 (most from about 2008 on), through our plug-in OBD2 cable. Older K-Line cars connect through the Krispy K-Line adaptor. Check yours on the supported vehicles list.
  • Standalone CAN modules: Haltech WB1/WB2 widebands, Haltech TCA thermocouple amplifiers, the AEM 8-channel thermocouple module and the AEM CSM6 sensor module.

How to lay out a multi-gauge

Everything is set up from your phone or laptop over WiFi. There's no app to install and no buttons to cycle through. Join the gauge's network Krispy_XXXX (password GetKrispy), open http://4.3.2.1 and go to Page Config. Each page gets a template and the readings to show on it:

  • Single Value or Dial for one reading, large.
  • Dual Value or Dual Dials for two related readings, such as boost and AFR, or oil pressure and RPM.
  • Quad Value or 4 Bars for four readings at once, for example a "health check" page with oil pressure, oil temperature, water temperature and voltage.
  • Histogram to see a reading over the last few seconds.
  • Extras such as a G-force ball (Haltech), 0–100 and quarter-mile timers, and tyre layouts.

A practical setup for a street car is one page you look at all the time (boost or water temperature), one "health check" page, and one or two pages for the occasional track day.

Warnings on every reading

Every page can have a minimum and a maximum warning. Low oil pressure, overboost, high water temperature, a lean AFR: when a reading crosses its limit, the gauge flashes a full-screen alert. Set the warnings once, and you don't have to keep watching every page yourself.

More than a gauge

Common questions

52mm or 60mm?

The 52mm fits any standard 52mm (2-1/16") gauge pod or dash hole. The 60mm has a larger screen, which helps on busy pages like Quad Value, and it also fits 52mm or 60mm mounts.

Does it need its own sensors?

No. KrispyGauge reads the sensors your ECU already has. If you want a reading your ECU doesn't measure, add the sensor to the ECU, or use a supported CAN sensor module.

Does it run on 24V?

Yes. It runs on 12V to 24V.

How do I update it?

Over WiFi from your phone or laptop. See how to update KrispyGauge firmware.

← All docs