Black Friday Deals! $100 off every Gauge
Docs / How to Set Up KrispyGauge as an Oil Temperature Gauge
How-to & Guides

How to Set Up KrispyGauge as an Oil Temperature Gauge

Show live oil temperature in °C or °F from your ECU or OBD2 port on a 52mm touchscreen gauge. Which ECUs and cars report it, setup and high-temp warnings.

KrispyGauge Rotating Dial page with oil temperature around 100 °C
Oil temperature on the Rotating Dial template: the scale turns, the number stays put.

Oil temperature tells you when an engine is properly warm and safe to work hard, and when it's getting too hot on a track day or a long tow. Coolant warms up first, but oil takes longer, and it's the oil that protects the bearings. KrispyGauge shows live oil temperature on a 52mm or 60mm colour touchscreen, in °C or °F, with a warning when it gets too hot.

What you need

  • A KrispyGauge (52mm or 60mm) to fit a standard gauge pod or dash panel.
  • Something that already measures oil temperature, which is one of these:
    • an aftermarket ECU with an oil temperature sensor wired in, or
    • a factory car whose ECU reports oil temperature over OBD2. Many do, but not all.

ECUs that send oil temperature

KrispyGauge reads oil temperature from these ECUs' CAN data:

Link and Holley ECUs work with KrispyGauge for other readings, but KrispyGauge doesn't currently read oil temperature from them.

Haltech and MaxxECU also send gearbox temperature, and a TurboLamik TCU sends it from the transmission controller. It's worth its own page if you tow, drag race or run a sequential.

Factory cars over OBD2

OBD2 has a standard reading for engine oil temperature, and KrispyGauge asks for it. Whether you get a number depends on the car. Plenty of ECUs report it, and plenty don't, even when the car shows oil temperature on its own dash.

The quickest way to find out is to try it: add Oil Tmp to a page (below) and run the engine. If a value appears, your car reports it. If it stays blank, it doesn't, and no OBD2 gauge will be able to show it. The OBD2 supported vehicles list covers cars that have been tested, and older K-Line cars can connect through the Krispy K-Line adaptor.

How to set it up

  1. Wire the gauge to your ECU's CAN bus or to the OBD2 port. The OBD2 setup guide covers wiring and power.
  2. With the ignition on, join the gauge's WiFi network Krispy_XXXX (password GetKrispy) and open http://4.3.2.1.
  3. Under Settings, choose your ECU type first, since changing it later resets your pages. Set Temperature to Celsius or Fahrenheit.
  4. Under Page Config, pick a template and set its channel to Oil Tmp (oil temperature).
  5. Set a maximum warning (below) and save.

Connection help is in connecting to the Web UI.

Set a high oil temperature warning

Give the oil temperature page a maximum warning. When the oil goes past it, the gauge flashes a full-screen alert, so you know to back off for a cool-down lap or pull over on a long climb. The right figure depends on your oil and engine, so check with your engine builder or oil maker. Many drivers start somewhere around 120–130 °C (250–265 °F).

You can also set a minimum warning as a "not warm yet" reminder, so the gauge tells you when it's too early to use full throttle.

Which template?

  • Dial (single) or Classic Needle for a traditional temperature gauge.
  • Background Fill fills the screen as the temperature rises, so you can read it from the corner of your eye.
  • Dual Value with oil and water temperature together, to see how far behind the oil is when warming up.
  • Quad Value for oil temperature, oil pressure, water temperature and battery voltage on one page.

Common questions

Can I wire an oil temperature sender straight to the KrispyGauge?

No. KrispyGauge reads over CAN only. Wire the sensor to your ECU, or to a CAN sensor module that KrispyGauge supports, such as the AEM CSM6.

My car shows oil temperature on its dash. Why is it blank on OBD2?

The factory dash often gets oil temperature from the ECU over the car's own internal network, without making it available through the standard OBD2 reading.

Can it show °F?

Yes. Temperature can be shown in Celsius or Fahrenheit.

← All docs